National Semiconductor Application Note 263 October 1999 Producing and manipulating the sine wave function is a common problem encountered by circuit designers. Sine wave circuits pose a significant design challenge because they represent a constantly controlled linear oscillator. Sine wave circuitry is required in a number of diverse areas, including audio testing, calibration equipment, transducer drives, power conditioning and automatic test equipment (ATE). Control of frequency, amplitude or distortion level is often required and all three parameters must be simultaneously controlled in many applications. configuration and oscillates at about 12 kHz. The remaining circuitry provides amplitude stability. The high impedance output at Q2's collector is fed to the input of the LM386 via the 10 F-1M series network. The 1M resistor in combination with the internal 50 k unit in the LM386 divides Q2's output by 20. This is necessary because the LM386 has a fixed gain of 20. In this manner the amplifier functions as a unity gain current buffer which will drive an 8 load. The positive peaks at the amplifier output are rectified and stored in the 5 F capacitor. This potential is fed to the base of Q3. Q3's collector current will vary with the difference between its base and emitter voltages. Since the emitter voltage is fixed by the LM313 1.2V reference, Q3 performs a comparison function and its collector current modulates Q1's base voltage. Q1, an emitter follower, provides servo controlled drive to the Q2 oscillator. If the emitter of Q2 is opened up and driven by a control voltage, the amplitude of the circuit output may be varied. The LM386 output will drive 5V (1.75 Vrms) peak-to-peak into 8 with about 2% distortion. A 3V power supply variation causes less than 0.1 dB amplitude shift at the output. A number of techniques utilizing both analog and digital approaches are available for a variety of applications. Each individual circuit approach has inherent strengths and weaknesses which must be matched against any given application (see table). Phase Shift Oscillator A simple inexpensive amplitude stabilized phase shift sine wave oscillator which requires one IC package, three transistors and runs off a single supply appears in Figure 1. Q2, in combination with the RC network comprises a phase shift Sine Wave Generation Techniques Sine Wave Generation Techniques 00748301 FIGURE 1. Phase-shift sine wave oscillators combine simplicity with versatility. This 12 kHz design can deliver 5 Vp-p to the 8 load with about 2% distortion. AN-263 (c) 2002 National Semiconductor Corporation AN007483 www.national.com AN-263 Sine-Wave-Generation Techniques Type Typical Typical Typical Frequency Distortion Amplitude Range (%) Stability Comments (%) Phase Shift 10 Hz-1 MHz 1-3 3 (Tighter Simple, inexpensive technique. Easily amplitude servo with Servo controlled. Resistively tunable over 2:1 range with Control) little trouble. Good choice for cost-sensitive, moderateperformance applications. Quick starting and settling. Wein Bridge 1 Hz-1 MHz 0.01 1 Extremely low distortion. Excellent for high-grade instrumentation and audio applications. Relatively difficult to tune -- requires dual variable resistor with good tracking. Take considerable time to settle after a step change in frequency or amplitude. LC 1 kHz-10 MHz 1-3 3 Difficult to tune over wide ranges. Higher Q than RC Negative types. Quick starting and easy to operate in high Resistance Tuning Fork frequency ranges. 60 Hz-3 kHz 0.25 0.01 Frequency-stable over wide ranges of temperature and supply voltage. Relatively unaffected by severe shock or vibration. Basically untunable. Crystal 30 kHz-200 MHz 0.1 1 Highest frequency stability. Only slight (ppm) tuning possible. Fragile. Triangle- < 1 Hz-500 kHz 1-2 1 Wide tuning range possible with quick settling to new Driven Break- frequency or amplitude. Point Shaper Triangle- < 1 Hz-500 kHz 0.3 0.25 Wide tuning range possible with quick settling to new Driven frequency or amplitude. Triangle and square wave also Logarithmic available. Excellent choice for general-purpose Shaper requirements needing frequency-sweep capability with low-distortion output. DAC-Driven < 1 Hz-500 kHz 0.3 0.25 Similar to above but DAC-generated triangle wave Logarithmic generally easier to amplitude-stabilize or vary. Also, Shaper DAC can be addressed by counters synchronized to a master system clock. ROM-Driven 1 Hz-20 MHz 0.1 0.01 DAC Powerful digital technique that yields fast amplitude and frequency slewing with little dynamic error. Chief detriments are requirements for high-speed clock (e.g., 8-bit DAC requires a clock that is 256 x output sine wave frequency) and DAC glitching and settling, which will introduce significant distortion as output frequency increases. network allow very high performance. The photo of Figure 3 shows the output of the circuit of Figure 2a. The upper trace is the oscillator output. The middle trace is the downward slope of the waveform shown greatly expanded. The slight aberration is due to crossover distortion in the FET-input LF155. This crossover distortion is almost totally responsible for the sum of the measured 0.01% distortion in this oscillator. The output of the distortion analyzer is shown in the bottom trace. In the circuit of Figure 2b, an electronic equivalent of the light bulb is used to control loop gain. The zener diode determines the output amplitude and the loop time constant is set by the 1M-2.2 F combination. Low Distortion Oscillation In many applications the distortion levels of a phase shift oscillator are unacceptable. Very low distortion levels are provided by Wein bridge techniques. In a Wein bridge stable oscillation can only occur if the loop gain is maintained at unity at the oscillation frequency. In Figure 2a this is achieved by using the positive temperature coefficient of a small lamp to regulate gain as the output attempts to vary. This is a classic technique and has been used by numerous circuit designers* to achieve low distortion. The smooth limiting action of the positive temperature coefficient bulb in combination with the near ideal characteristics of the Wein www.national.com 2 plitude controllable oscillator. The LH0002 buffer provides low impedance drive to the LS-52 audio transformer. A voltage gain of 100 is achieved by driving the secondary of the transformer and taking the output from the primary. A current-sensitive negative absolute value amplifier composed of two amplifiers of an LF347 quad generates a negative rectified feedback signal. This is compared to the LM329 DC reference at the third LF347 which amplifies the difference at a gain of 100. The 10 F feedback capacitor is used to set the frequency response of the loop. The output of this amplifier controls the amplitude of the LM3900 oscillator thereby closing the loop. As shown the circuit oscillates at 1 kHz with under 0.1% distortion for a 100 Vrms (285 Vp-p) output. If the summing resistors from the LM329 are replaced with a potentiometer the loop is stable for output settings ranging from 3 Vrms to 190 Vrms (542 Vp-p!) with no change in frequency. If the DAC1280 D/A converter shown in dashed lines replaces the LM329 reference, the AC output voltage can be controlled by the digital code input with 3 digit calibrated accuracy. (Continued) The 2N3819 FET, biased by the voltage across the 2.2 F capacitor, is used to control the AC loop gain by shunting the feedback path. This circuit is more complex than Figure 2a but offers a way to control the loop time constant while maintaining distortion performance almost as good as in Figure 2. Note: * Including William Hewlett and David Packard who built a few of these type circuits in a Palo Alto garage about forty years ago. High Voltage AC Calibrator Another dimension in sine wave oscillator design is stable control of amplitude. In this circuit, not only is the amplitude stabilized by servo control but voltage gain is included within the servo loop. A 100 Vrms output stabilized to 0.025% is achieved by the circuit of Figure 4. Although complex in appearance this circuit requires just 3 IC packages. Here, a transformer is used to provide voltage gain within a tightly controlled servo loop. The LM3900 Norton amplifiers comprise a 1 kHz am- 00748302 (a) 00748303 (b) FIGURE 2. A basic Wein bridge design (a) employs a lamp's positive temperature coefficient to achieve amplitude stability. A more complex version (b) provides the same feature with the additional advantage of loop time-constant control. 3 www.national.com AN-263 Low Distortion Oscillation AN-263 High Voltage AC Calibrator (Continued) Trace Vertical Horizontal Top 10V/DIV 10 ms/DIV Middle 1V/DIV 500 ns/DIV Bottom 0.5V/DIV 500 ns/DIV 00748304 FIGURE 3. Low-distortion output (top trace) is a Wein bridge oscillator feature. The very low crossover distortion level (middle) results from the LF155's output stage. A distortion analyzer's output signal (bottom) indicates this design's 0.01% distortion level. 00748305 A1-A3 = 14 LM3900 A4 = LH0002 A5-A7 = 14 LF347 T1 = UTC LS-52 All diodes = 1N914 * = low-TC, metal-film types FIGURE 4. Generate high-voltage sine waves using IC-based circuits by driving a transformer in a step-up mode. You can realize digital amplitude control by replacing the LM329 voltage reference with the DAC1287. www.national.com 4 All of the preceding circuits rely on RC time constants to achieve resonance. LC combinations can also be used and offer good frequency stability, high Q and fast starting. In Figure 5 a negative resistance configuration is used to generate the sine wave. The Q1-Q2 pair provides a 15 A current source. Q2's collector current sets Q3's peak collector current. The 300 k resistor and the Q4-Q5 LM394 00748306 FIGURE 5. LC sine wave sources offer high stability and reasonable distortion levels. Transistors Q1 through Q5 implement a negative-resistance amplifier. The LM329, LF353 combination eliminates power-supply dependence. low frequencies achievable with tuning forks are not available from crystals. In Figure 6, a 1 kHz fork is used in a feedback configuration with Q2, one transistor of an LM3045 array. Q1 provides zener drive to the oscillator circuit. The need for amplitude stabilization is eliminated by allowing the oscillator to go into limit. This is a conventional technique in fork oscillator design. Q3 and Q4 provide edge speed-up and a 5V output for TTL compatibility. Emitter follower Q5 is used to drive an LC filter which provides a sine wave output. Figure 7, trace A shows the square wave output while trace B depicts the sine wave output. The 0.7% distortion in the sine wave output is shown in trace C, which is the output of a distortion analyzer. Resonant Element Oscillator--Tuning Fork All of the above oscillators rely on combinations of passive components to achieve resonance at the oscillation frequency. Some circuits utilize inherently resonant elements to achieve very high frequency stability. In Figure 6 a tuning fork is used in a feedback loop to achieve a stable 1 kHz output. Tuning fork oscillators will generate stable low frequency sine outputs under high mechanical shock conditions which would fracture a quartz crystal. Because of their excellent frequency stability, small size and low power requirements, they have been used in airborne applications, remote instrumentation and even watches. The 5 www.national.com AN-263 matched pair accomplish a voltage-to-current conversion that decreases Q3's base current when its collector voltage rises. This negative resistance characteristic permits oscillation. The frequency of operation is determined by the LC in the Q3-Q5 collector line. The LF353 FET amplifier provides gain and buffering. Power supply dependence is eliminated by the zener diode and the LF353 unity gain follower. This circuit starts quickly and distortion is inside 1.5%. Negative Resistance Oscillator AN-263 Resonant Element Oscillator--Tuning Fork (Continued) 00748307 Q1-Q5 = LM3045 array Y1 = 1 kHz tuning fork, Fork Standards Inc. All capacitors in F FIGURE 6. Tuning fork based oscillators don't inherently produce sinusoidal outputs. But when you do use them for this purpose, you achieve maximum stability when the oscillator stage (Q1, Q2) limits. Q3 and Q4 provide a TTL compatible signal, which Q5 then converts to a sine wave. 00748308 Trace Vertical Top 5V/DIV Middle 50V/DIV Bottom 0.2V/DIV Horizontal 500 s/DIV FIGURE 7. Various output levels are provided by the tuning fork oscillator shown in Figure 6. This design easily produces a TTL compatible signal (top trace) because the oscillator is allowed to limit. Low-pass filtering this square wave generates a sine wave (middle). The oscillator's 0.7% distortion level is indicated (bottom) by an analyzer's output. www.national.com 6 Quartz crystals allow high frequency stability in the face of changing power supply and temperature parameters. Figure 8a shows a simple 100 kHz crystal oscillator. This Colpitts class circuit uses a JFET for low loading of the crystal, aiding stability. Regulation will eliminate the small effects ( 5 ppm for 20% shift) that supply variation has on this circuit. Shunting the crystal with a small amount of capacitance allows very fine trimming of frequency. Crystals typically drift less than 1 ppm/C and temperature controlled ovens can be used to eliminate this term (Figure 8b). The RC feedback values will depend upon the thermal time constants of the oven used. The values shown are typical. The temperature of the oven should be set so that it coincides with the crystal's zero temperature coefficient or "turning point" temperature which is manufacturer specified. An alternative to temperature control uses a varactor diode placed across the Approximation Methods All of the preceding circuits are inherent sine wave generators. Their normal mode of operation supports and maintains a sinusoidal characteristic. Another class of oscillator is made up of circuits which approximate the sine function through a variety of techniques. This approach is usually more complex but offers increased flexibility in controlling amplitude and frequency of oscillation. The capability of this type of circuit for a digitally controlled interface has markedly increased the popularity of the approach. 00748309 (a) 00748310 (b) 00748311 (c) FIGURE 8. Stable quartz-crystal oscillators can operate with a single active device (a). You can achieve maximum frequency stability by mounting the oscillator in an oven and using a temperature-controlling circuit (b). A varactor network (c) can also accomplish crystal fine tuning. Here, the varactor replaces the oven and retunes the crystal by changing its load capacitances. 7 www.national.com AN-263 crystal. The varactor is biased by a temperature dependent voltage from a circuit which could be very similar to Figure 8b without the output transistor. As ambient temperature varies the circuit changes the voltage across the varactor, which in turn changes its capacitance. This shift in capacitance trims the oscillator frequency. Resonant Element Oscillator--Quartz Crystal AN-263 pensation for the shaper diodes. Figure 10 shows the circuit's performance. Trace A is the filtered output (note 1000 pF capacitor across the output amplifier). Trace B shows the waveform with no filtering (1000 pF capacitor removed) and trace C is the output of a distortion analyzer. In trace B the breakpoint action is just detectable at the top and bottom of the waveform, but all the breakpoints are clearly identifiable in the distortion analyzer output of trace C. In this circuit, if the amplitude or symmetry of the input triangle wave shifts, the output waveform will degrade badly. Typically, a D/A converter will be used to provide input drive. Distortion in this circuit is less than 1.5% for a filtered output. If no filter is used, this figure rises to about 2.7%. Sine Approximation--Breakpoint Shaper Figure 9 diagrams a circuit which will "shape" a 20 Vp-p wave input into a sine wave output. The amplifiers serve to establish stable bias potentials for the diode shaping network. The shaper operates by having individual diodes turn on or off depending upon the amplitude of the input triangle. This changes the gain of the output amplifier and gives the circuit its characteristic non-linear, shaped output response. The values of the resistors associated with the diodes determine the shaped waveform's appearance. Individual diodes in the DC bias circuitry provide first order temperature com- 00748312 All diodes = 1N4148 All op amps = 14 LF347 FIGURE 9. Breakpoint shaping networks employ diodes that conduct in direct proportion to an input triangle wave's amplitude. This action changes the output amplifier's gain to produce the sine function. 00748313 Trace Vertical A 5V/DIV Horizontal B 5V/DIV C 0.5V/DIV 20 s/DIV FIGURE 10. A clean sine wave results (trace A) when Figure 9 circuit's output includes a 1000 pF capacitor. When the capacitor isn't used, the diode network's breakpoint action becomes apparent (trace B). The distortion analyzer's output (trace C) clearly shows all the breakpoints. www.national.com 8 Figure 11 shows a complete sine wave oscillator which may be tuned from 1 Hz to 10 kHz with a single variable resistor. Amplitude stability is inside 0.02%/C and distortion is 0.35%. In addition, desired frequency shifts occur instantaneously because no control loop time constants are employed. The circuit works by placing an integrator inside the positive feedback loop of a comparator. The LM311 drives symmetrical, temperature-compensated clamp arrangement. The output of the clamp biases the LF356 integrator. 00748314 All diodes = 1N4148 Adjust symmetry and waveshape controls for minimum distortion * LM311 Ground Pin (Pin 1) at -15V FIGURE 11. Logarithmic shaping schemes produce a sine wave oscillator that you can tune from 1 Hz to 10 kHz with a single control. Additionally, you can shift frequencies rapidly because the circuit contains no control-loop time constants. two complementary voltages are each gated by the 2N4393 FET switches, which are controlled by the LM311 output. The frequency of oscillation will now vary in direct proportion to the control input. In addition, because the amplitude of this circuit is controlled by limiting, rather than a servo loop, response to a control step or ramp input is almost instantaneous. For a 0V-10V input the output will run over 1 Hz to 30 Sine Approximation--Voltage Controlled Sine Oscillator Figure 12 details a modified but extremely powerful version of Figure 11. Here, the input voltage to the LF356 integrator is furnished from a control voltage input instead of the zener diode bridge. The control input is inverted by the LF351. The 9 www.national.com AN-263 The LF356 integrates this current into a linear ramp at its output. This ramp is summed with the clamp output at the LM311 input. When the ramp voltage nulls out the bound voltage, the comparator changes state and the integrator output reverses. The resultant, repetitive triangle waveform is applied to the sine shaper configuration. The sine shaper utilizes the non-linear, logarithmic relationship between Vbe and collector current in transistors to smooth the triangle wave. The LM394 dual transistor is used to generate the actual shaping while the 2N3810 provides current drive. The LF351 allows adjustable, low impedance, output amplitude control. Waveforms of operation are shown in Figure 14. Sine Approximation--Logarithmic Shaping AN-263 Sine Approximation--Voltage Controlled Sine Oscillator (Continued) control voltage vs output frequency will be within 0.25%. Figure 13 shows the response of this circuit (waveform B) to a 10V ramp (waveform A). kHz with less than 0.4% distortion. In addition, linearity of 00748315 Adjust distortion for minimum at 1 Hz to 10 Hz Adjust full-scale for 30 kHz at 10V input All diodes = 1N4148 * Match to 0.1% FIGURE 12. A voltage-tunable oscillator results when Figure 11's design is modified to include signal-levelcontrolled feedback. Here, FETs switch the integrator's input so that the resulting summing-junction current is a function of the input control voltage. This scheme realizes a frequency range of 1 Hz to 30 kHz for a 0V to 10V input. 00748316 FIGURE 13. Rapid frequency sweeping is an inherent feature of Figure 12's voltage-controlled sine wave oscillator. You can sweep this VCO from 1 Hz to 30 kHz with a 10V input signal; the output settles quickly. www.national.com 10 Digital methods may be used to approximate sine wave operation and offer the greatest flexibility at some increase in complexity. Figure 15 shows a 10-bit IC D/A converter driven from up/down counters to produce an amplitude-stable triangle current into the LF357 FET amplifier. The LF357 is used to drive a shaper circuit of the type shown in Figure 11. The output amplitude of the sine wave is stable and the frequency is solely dependent on the clock used to drive the counters. If the clock is crystal controlled, the output sine wave will reflect the high frequency stability of the crystal. In this example, 10 binary bits are used to drive the DAC so the output frequency will be 1/1024 of the clock frequency. If a sine coded read-only-memory is placed between the counter 00748317 Trace Vertical Horizontal A 20V/DIV B 20V/DIV C 10V/DIV D 10V/DIV E 0.5V/DIV 20 s/DIV FIGURE 14. Logarithmic shapers can utilize a variety of circuit waveforms. The input to the LF356 integrator (Figure 11) appears here as trace A. The LM311's input (trace B) is the summed result of the integrator's triangle output (C) and the LM329's clamped waveform. After passing through the 2N3810/LM394 shaper stage, the resulting sine wave is amplified by the LF351 (D). A distortion analyzer's output (E) represents a 0.35% total harmonic distortion. 11 www.national.com AN-263 outputs and the DAC, the sine shaper may be eliminated and the sine wave output taken directly from the LF357. This constitutes an extremely powerful digital technique for generating sine waves. The amplitude may be voltage controlled by driving the reference terminal of the DAC. The frequency is again established by the clock speed used and both may be varied at high rates of speed without introducing significant lag or distortion. Distortion is low and is related to the number of bits of resolution used. At the 8-bit level only 0.5% distortion is seen (waveforms, Figure 16; graph, Figure 17) and filtering will drop this below 0.1%. In the photo of Figure 16 the ROM directed steps are clearly visible in the sine waveform and the DAC levels and glitching show up in the distortion analyzer output. Filtering at the output amplifier does an effective job of reducing distortion by taking out these high frequency components. Sine Approximation--Digital Methods AN-263 Sine Approximation--Digital Methods (Continued) 00748318 MM74C00 = NAND MM74C32 = OR MM74C74 = D flip-flop MM74193 = counters FIGURE 15. Digital techniques produce triangular waveforms that methods employed in Figure 11 can then easily convert to sine waves. This digital approach divides the input clock frequency by 1024 and uses the resultant 10 bits to drive a DAC. The DAC's triangular output -- amplified by the LF357 -- drives the log shaper stage. You could also eliminate the log shaper and place a sine-coded ROM between the counters' outputs and the DAC, then recover the sine wave at point A. www.national.com 12 AN-263 Sine Approximation--Digital Methods (Continued) 00748319 Trace Vertical Horizontal Sine Wave 1V/DIV 200 s/DIV Analyzer 0.2V/DIV FIGURE 16. An 8-bit sine coded ROM version of Figure 15's circuit produces a distortion level less than 0.5%. Filtering the sine output -- shown here with a distortion analyzer's trace -- can reduce the distortion to below 0.1%. 00748320 FIGURE 17. Distortion levels decrease with increasing digital word length. Although additional filtering can considerably improve the distortion levels (to 0.1% from 0.5% for the 8-bit case), you're better off using a long digital word. 13 www.national.com Sine Wave Generation Techniques Notes LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: AN-263 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.